nodebots-hcsr04

0.5.0 • Public • Published

HC-SR04 Ultrasonic Sensor package for Johnny Five

By default HCSR04 ultrasonic sensors don't work with johnny-five. This is because they use a custom protocol that requires pulseIn which is not part of the core firmata.

To overcome this for arduinos you can use a custom firmata (installable from this package) however for devices like Raspberry Pis, you can't directly connect these devices.

As such a "BackPack" provides the ability to use devices such as this using I2C which is supported by all Johnny-Five boards. More info on this can be found at NodeBots Interchange.

Installation and getting started

Installation can be done manually using:

npm install nodebots-hcsr04

However if you are using johnny five then you can use Interchange instead

Firmware installation using Interchange

Interchange is the preferred method of installation with the following instructions being the way to do it.

A "supported board" means that precompiled binaries are shipped in the repo. This means you don't need to install arduino to be able to install this on your board (this is especially useful if you're on a chromebook).

To get started with interchange:

npm install nodebots-interchange

This will place the interchange application in your node_modules/.bin folder and you can either run this directly or add ./node_modules/.bin to your path in order to run it. The sections below explain how to use it and see the Interchange documentation for more details and examples.

I2C Backpack.

The I2C backpack is the preferred method of use as it's a separate module, and won't impact the performance of your main Arduino running firmata. In addition you can use this on any nodebots device that supports an I2C connection through it's IO Plugin (eg RPI, BeagleBone, Tessel etc).

Currently supported devices (and their board names):

  • Arduino Nano (preferred) (nano)
  • Arduino ProMini (pro-mini)
  • Arduino Uno (uno)

To install, you need to put your backpack into "configuration mode". After flashing, this will configure the board with firmware IDs and default I2C address. Simply jump pin D2 HIGH (connect D2 to 5V). Once complete, remove this jumper to use normally (see wiring diagram below).

Configuration mode for Interchange Backpack

Then use interchange to flash and configure the board.

interchange install hc-sr04 -p <port> -a <board=[nano|uno|pro-mini]>

Where <board> is the type of board using the names given above and <port> is the name or address of the serial port (eg: /dev/tty.usbserial1450).

To use the ping sensor, wire it up as the diagram below shows and then you can use it with the Johnny Five controller. Note that the trigger and echo are wired to the same pin which is D8 on the backpack.

Circuit for I2C backpack

Custom firmata

If you have an arduino and want to use a custom firmata you can simply install the firmware directly.

interchange install hc-sr04 --firmata -a <board> -p <port>

Currently supported devices are (and their name for use above):

  • Arduino Uno (uno)
  • Arduino Nano (nano)
  • Arduino ProMini (pro-mini).

If you want to use a different board then open the firmware/build/hcsr04_firmata directory and compile the files using Arduino or GCC. Upload using your normal process from there.

Developing

Generally speaking it's a case of simply cloning the repo, doing an npm install and doing development as normal.

One thing to note is that all pull requests require rebuilding the application in order to generate a new set of builds. For this it's handy to make sure you have the ARDUINO_PATH environment variable set and then a grunt compile is all you need.

ARDUINO_PATH is simply a full path to the arduino run time, noting that you also must have a version more recent than 1.6.2 in order to get command line benefits.

To make a build, simply grunt compile and it should do everything needed.

Arduino Version

Currently this repo uses the Arduino 1.6.6 build in order to maintain consistency of build process with regards to where compiled Hexes end up.

Tests

Before issuing a pull request, please deliver appropriate tests and also make sure the test suite has been run completely - this will ensure build and hex files are in the right location.

Package Sidebar

Install

npm i nodebots-hcsr04

Weekly Downloads

1

Version

0.5.0

License

MIT

Last publish

Collaborators

  • ajfisher