iobroker.rpi2

1.3.2 • Public • Published

Logo ioBroker RPI-Monitor Adapter

Number of Installations Number of Installations NPM version

Translation status Downloads

RPI-Monitor implementation for integration into ioBroker. It is the same implementation as for iobroker.rpi, but with GPIOs.

Important Information

Works only with node >= 0.12

ioBroker needs special permissions to control GPIOs. On most Linux distributions this can be achieved by adding the ioBroker user to the gpio group (recommended) or running ioBroker under root (less secure).

Installation

After installation you have to configure all required modules via administration page.

After start of iobroker.rpi, all selected modules generates an object tree in ioBroker within rpi.. e.g. rpi.0.cpu

Be sure, that python and build-essential are installed:

sudo apt-get update
sudo apt-get install -y build-essential python

Following Objects are available after selection:

CPU

  • cpu_frequency
  • load1
  • load5
  • load15

Raspberry (vcgencmd is required)

  • cpu_voltage
  • mem_arm
  • mem_gpu

Memory

  • memory_available
  • memory_free
  • memory_total

Network (eth0)

  • net_received
  • net_send

SDCard

  • sdcard_boot_total
  • sdcard_boot_used
  • sdcard_root_total
  • sdcard_root_used

Swap

  • swap_total
  • swap_used

Temperature

  • soc_temp

Uptime

  • uptime

WLAN

  • wifi_received
  • wifi_send

Configuration

On configuration page you can select following modules:

  • CPU
  • Raspberry
  • Memory
  • Network
  • SDCard
  • Swap
  • Temperature
  • Uptime
  • WLAN

Logfiles / Configuration Settings

Features

Todo

Tested Hardware

  • Odroid C1
  • Raspberry Pi 1

GPIOs

You can read and control GPIOs too. All what you need to do is to configure in the settings the GPIOs options (additional tab).

GPIOs

After some ports are enabled following states appear in the object tree:

  • rpi.0.gpio.PORT.state

The numeration of ports is BCM (BroadComm pins on chip). You can get the enumeration with gpio readall. For instance PI2:

+-----+-----+---------+------+---+---Pi 2---+---+------+---------+-----+-----+
| BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
+-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
|     |     |    3.3v |      |   |  1 || 2  |   |      | 5v      |     |     |
|   2 |   8 |   SDA.1 | ALT0 | 1 |  3 || 4  |   |      | 5V      |     |     |
|   3 |   9 |   SCL.1 | ALT0 | 1 |  5 || 6  |   |      | 0v      |     |     |
|   4 |   7 | GPIO. 7 |   IN | 1 |  7 || 8  | 0 | IN   | TxD     | 15  | 14  |
|     |     |      0v |      |   |  9 || 10 | 1 | IN   | RxD     | 16  | 15  |
|  17 |   0 | GPIO. 0 |   IN | 0 | 11 || 12 | 0 | IN   | GPIO. 1 | 1   | 18  |
|  27 |   2 | GPIO. 2 |   IN | 0 | 13 || 14 |   |      | 0v      |     |     |
|  22 |   3 | GPIO. 3 |   IN | 0 | 15 || 16 | 0 | IN   | GPIO. 4 | 4   | 23  |
|     |     |    3.3v |      |   | 17 || 18 | 0 | IN   | GPIO. 5 | 5   | 24  |
|  10 |  12 |    MOSI |   IN | 0 | 19 || 20 |   |      | 0v      |     |     |
|   9 |  13 |    MISO |   IN | 0 | 21 || 22 | 1 | IN   | GPIO. 6 | 6   | 25  |
|  11 |  14 |    SCLK |   IN | 0 | 23 || 24 | 1 | IN   | CE0     | 10  | 8   |
|     |     |      0v |      |   | 25 || 26 | 1 | IN   | CE1     | 11  | 7   |
|   0 |  30 |   SDA.0 |   IN | 1 | 27 || 28 | 1 | IN   | SCL.0   | 31  | 1   |
|   5 |  21 | GPIO.21 |   IN | 1 | 29 || 30 |   |      | 0v      |     |     |
|   6 |  22 | GPIO.22 |   IN | 1 | 31 || 32 | 0 | IN   | GPIO.26 | 26  | 12  |
|  13 |  23 | GPIO.23 |   IN | 0 | 33 || 34 |   |      | 0v      |     |     |
|  19 |  24 | GPIO.24 |   IN | 0 | 35 || 36 | 0 | IN   | GPIO.27 | 27  | 16  |
|  26 |  25 | GPIO.25 |  OUT | 1 | 37 || 38 | 0 | IN   | GPIO.28 | 28  | 20  |
|     |     |      0v |      |   | 39 || 40 | 0 | IN   | GPIO.29 | 29  | 21  |
+-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
| BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
+-----+-----+---------+------+---+---Pi 2---+---+------+---------+-----+-----+

DHTxx/AM23xx Sensors

You can read from DHT11, DHT22 and AM2302 temperature/humidity sensors.

Connect such a sensor to a GPIO pin as described on the node-dht-sensor package page. Multiple sensors can be connected to multiple pins (this is not a bus system) as discussed.

Changelog

1.3.2 (2022-02-17)

  • Important: This version requires at leas js-controller 3.3
  • (Apollon77) Stop the adapter when GPIO module is configured but not working due to a needed rebuild that js-controller can pick up

1.3.1 (2021-07-16)

  • (Apollon77) Prevent js-controller 3.3 warnings

1.3.0 (2021-07-16)

  • (asgothian) Fix to get CPU frequencies also on Raspi 4
  • (raintor) Add support for DHTxx/AM23xx Sensors
  • (raintor) Configure internal Pull UP/Down Resistor
  • (raintor) Add port 'label'/'friendly name' to GPIO config

1.2.0 (2020-01-17)

  • (janfromberlin) GPIO configuration as output with defined initial value
  • (foxriver76) No longer use adapter.objects
  • (Apollon77) Adjust gpio errors

1.1.1

  • (Apollon77) Error messages for not existing values are logged only once

1.1.0

  • (Apollon77) Nodejs 10 support

1.0.0 (2018-08-20)

  • (bluefox) Admin3 support

0.3.2 (2017-11-29)

  • (Homoran) fixed Mem available readings on Stretch

0.3.1 (2017-01-11)

  • (olifre) Fixup swap_used calculation.

0.2.2 (2016-12-01)

  • (bluefox) Add GPIO direction indication

0.2.2 (2016-11-22)

  • (bluefox) Use BCM enumeration

0.2.1 (2016-10-29)

  • (bluefox) fix start of adapter

0.2.0 (2016-10-23)

  • (bluefox) just version change

0.1.1 (2016-10-13)

  • (bluefox) implement GPIOs control

0.0.4 (2016-03-25)

  • (bluefox) Try catch by eval (bluefox) do not process if exec fails

0.0.3 (2015-12-28)

  • (husky-koglhof) Fixed value calc. Set Value to 2 digits

0.0.2 (2015-12-26)

  • (husky-koglhof) Workaround for node 0.10.x
  • (bluefox) Some Fixes

0.0.1 (2015-12-23)

  • Initial commit. Alpha Version.

License

Copyright (c) 2015-2022 husky-koglhof husky.koglhof@icloud.com

MIT License

Dependents (0)

Package Sidebar

Install

npm i iobroker.rpi2

Weekly Downloads

229

Version

1.3.2

License

MIT

Unpacked Size

347 kB

Total Files

16

Last publish

Collaborators

  • foxriver76
  • iobluefox
  • bluefox
  • apollon77
  • ldittmar
  • alcalzone
  • mcm1957
  • pmant
  • matten-matten
  • simatec
  • dkleber89
  • raintonr
  • issi
  • ciddi89
  • dutchmannl
  • patrickwaltherh
  • ruhr70
  • arteck
  • meistertr
  • prinzeisenherz1
  • nisiode
  • zefau
  • algar42
  • garfonso
  • forelleblau
  • buzzy1337
  • pdbjjens
  • unclesamswiss
  • _shojo_
  • swedish.chef
  • thiemoh
  • sven-s-ter