iobroker.rpi2

2.2.2 • Public • Published

Logo ioBroker RPI-Monitor Adapter

NPM version Downloads Number of Installations Current version in stable repository

NPM

Tests: Test and Release RPI-Monitor implementation for integration into ioBroker. It is the same implementation as for iobroker.rpi, but with GPIOs.

Important Information

Works only with node >= 18

ioBroker needs special permissions to control GPIOs. On most Linux distributions this can be achieved by adding the ioBroker user to the gpio group (recommended) or running ioBroker under root (less secure).

For gpio to work, you need to install libgpiod, before installing the adapter, like this: sudo apt-get install -y libgpiod-dev

Installation

After installation you have to configure all required modules via administration page.

After start of iobroker.rpi, all selected modules generates an object tree in ioBroker within rpi.. e.g. rpi.0.cpu

Be sure, that python and build-essential are installed:

sudo apt-get update
sudo apt-get install -y build-essential python
sudo apt-get install -y libgpiod-dev

(the last one is only necessary, if you want to work with GPIOs)

Following Objects are available after selection:

CPU

  • cpu_frequency
  • load1
  • load5
  • load15

Raspberry (vcgencmd is required)

  • cpu_voltage
  • mem_arm
  • mem_gpu

Memory

  • memory_available
  • memory_free
  • memory_total

Network (eth0)

  • net_received
  • net_send

SDCard

  • sdcard_boot_total
  • sdcard_boot_used
  • sdcard_root_total
  • sdcard_root_used

Swap

  • swap_total
  • swap_used

Temperature

  • soc_temp

Uptime

  • uptime

WLAN

  • wifi_received
  • wifi_send

Configuration

On configuration page you can select following modules:

  • CPU
  • Raspberry
  • Memory
  • Network
  • SDCard
  • Swap
  • Temperature
  • Uptime
  • WLAN

Logfiles / Configuration Settings

Features

Todo

Tested Hardware

  • Odroid C1
  • Raspberry Pi 1

GPIOs

You can read and control GPIOs too. All what you need to do is to configure in the settings the GPIOs options (additional tab).

GPIOs

After some ports are enabled following states appear in the object tree:

  • rpi.0.gpio.PORT.state

The numeration of ports is BCM (BroadComm pins on chip). You can get the enumeration with gpio readall. For instance PI2:

+-----+-----+---------+------+---+---Pi 2---+---+------+---------+-----+-----+
| BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
+-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
|     |     |    3.3v |      |   |  1 || 2  |   |      | 5v      |     |     |
|   2 |   8 |   SDA.1 | ALT0 | 1 |  3 || 4  |   |      | 5V      |     |     |
|   3 |   9 |   SCL.1 | ALT0 | 1 |  5 || 6  |   |      | 0v      |     |     |
|   4 |   7 | GPIO. 7 |   IN | 1 |  7 || 8  | 0 | IN   | TxD     | 15  | 14  |
|     |     |      0v |      |   |  9 || 10 | 1 | IN   | RxD     | 16  | 15  |
|  17 |   0 | GPIO. 0 |   IN | 0 | 11 || 12 | 0 | IN   | GPIO. 1 | 1   | 18  |
|  27 |   2 | GPIO. 2 |   IN | 0 | 13 || 14 |   |      | 0v      |     |     |
|  22 |   3 | GPIO. 3 |   IN | 0 | 15 || 16 | 0 | IN   | GPIO. 4 | 4   | 23  |
|     |     |    3.3v |      |   | 17 || 18 | 0 | IN   | GPIO. 5 | 5   | 24  |
|  10 |  12 |    MOSI |   IN | 0 | 19 || 20 |   |      | 0v      |     |     |
|   9 |  13 |    MISO |   IN | 0 | 21 || 22 | 1 | IN   | GPIO. 6 | 6   | 25  |
|  11 |  14 |    SCLK |   IN | 0 | 23 || 24 | 1 | IN   | CE0     | 10  | 8   |
|     |     |      0v |      |   | 25 || 26 | 1 | IN   | CE1     | 11  | 7   |
|   0 |  30 |   SDA.0 |   IN | 1 | 27 || 28 | 1 | IN   | SCL.0   | 31  | 1   |
|   5 |  21 | GPIO.21 |   IN | 1 | 29 || 30 |   |      | 0v      |     |     |
|   6 |  22 | GPIO.22 |   IN | 1 | 31 || 32 | 0 | IN   | GPIO.26 | 26  | 12  |
|  13 |  23 | GPIO.23 |   IN | 0 | 33 || 34 |   |      | 0v      |     |     |
|  19 |  24 | GPIO.24 |   IN | 0 | 35 || 36 | 0 | IN   | GPIO.27 | 27  | 16  |
|  26 |  25 | GPIO.25 |  OUT | 1 | 37 || 38 | 0 | IN   | GPIO.28 | 28  | 20  |
|     |     |      0v |      |   | 39 || 40 | 0 | IN   | GPIO.29 | 29  | 21  |
+-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
| BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
+-----+-----+---------+------+---+---Pi 2---+---+------+---------+-----+-----+

DHTxx/AM23xx Sensors

You can read from DHT11, DHT22 and AM2302 temperature/humidity sensors.

Connect such a sensor to a GPIO pin as described on the node-dht-sensor package page. Multiple sensors can be connected to multiple pins (this is not a bus system) as discussed.

Changelog

2.2.2 (2024-11-02)

  • (simatec) responsive design for settings page added

2.2.1 (2024-10-15)

  • (Garfonso) temperature has now proper role and type.

2.2.0 (2024-10-15)

  • (Garfonso) rebuild config in JSONConfig.

2.1.2 (2024-10-13)

  • (Garfonso) transmit all GPIO changes to iobroker states.

2.1.1 (2024-10-13)

  • (Garfonso) fix gpio undefined errors.

License

MIT License

Copyright (c) 2024 Garfonso garfonso@mobo.info

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Package Sidebar

Install

npm i iobroker.rpi2

Weekly Downloads

586

Version

2.2.2

License

MIT

Unpacked Size

123 kB

Total Files

23

Last publish

Collaborators

  • foxriver76
  • iobluefox
  • bluefox
  • apollon77
  • ldittmar
  • alcalzone
  • mcm1957
  • pmant
  • matten-matten
  • simatec
  • dkleber89
  • raintonr
  • issi
  • ciddi89
  • dutchmannl
  • patrickwaltherh
  • ruhr70
  • arteck
  • meistertr
  • prinzeisenherz1
  • nisiode
  • zefau
  • algar42
  • garfonso
  • forelleblau
  • buzzy1337
  • pdbjjens
  • unclesamswiss
  • _shojo_
  • swedish.chef
  • thiemoh
  • sven-s-ter