Noteworthy Puppy Movies

    grunt-surveil

    0.1.2 • Public • Published

    grunt-surveil

    Description

    This grunt task enables you to trigger tasks whenever files are added, changed, or removed. It's very much like grunt-contrib-watch but with a few different design choices:

    • surveil enables you to control how your tasks gets invoked, that is, before the tasks are being run you have a chance to modify grunt configurations to enable running tasks on only changed files. You can even tell grunt-surveil to skip a task at runtime depending on which file changed.
    • It also sets up its file watchers once, and will then re-use those until grunt is exited. This comes with a few got-cha's that you can read about below, but ultimately means that performance and responsiveness increases a lot when running for a long time and/or using common tasks.

    Never-ending file watchers

    If you watch a lot of files/directories, triggering tasks can be a bit pain when using most other watchers. Re-watching thousands of nodes takes a while, even on an SSD.

    This also causes responsiveness of the watch task to go down noticeably (if files are changed during triggered tasks, you won't retroactively get these file changes after the tasks are done, and have to "touch" the files once more to trigger the watch again.)

    This is part of what grunt-surveil has been designed to mitigate.

    Usage

    Install

    npm install --save-dev grunt-surveil
    

    Then edit your Gruntfile.js with the configuration (see below) and load the task with grunt.loadNpmTasks("grunt-surveil").

    Configuration

    Like grunt-contrib-watch, grunt-surveil is a single-target grunt task that uses multi-task configuration.

    Parameters (global)

    delay: 100

    The number of milliseconds to delay executing tasks when files change. This can be good to adjust if you want to do more "bulk runs."

    emitOnAllTargets: false

    Whether to trigger all targets when files change. The default behavior of gaze is to emit file changes to all watch instances. By default in grunt-surveil, this behavior is disabled to provide more granular execution of tasks but might not play ball with every task out there.

    rewriteThreshold: 100

    The number of milliseconds that files are ignored after tasks has been run. It is only used when a task has the rewritesWatchedFiles flag enabled.

    Parameters (per target)

    src: "<%= foo.bar %>/**/baz/*.js"

    The source files to watch on. Can be any pattern that is supported by grunt.

    tasks: ["foo", "bar:baz"]

    The list of grunt tasks to execute when src files change. The tasks will be executed in order.

    prepare: function(changedFiles, task)

    This callback gets invoked once for every task in the task array. If you decide that the current task doesn't need to be executed, returning false from this callback will make grunt-surveil to ignore that task.

    rewritesWatchedFiles: false

    This flag can be used on targets that you know will overwrite watched files. Due to re-using file watchers under task executions, these watches will trigger changes on files that the executed tasks changes. This prohibits grunt-surveil from triggering during that time.

    Examples

    A typical configuration might look something like this:

    grunt.initConfig( {
        surveil: {
            javascript: {
                src: ["gruntfile.js", "lib/**/*.js"],
                prepare: function( changedFiles, task ) {
                    grunt.config( "eslint.partial", changedFiles );
                },
                tasks: ["eslint:partial"]
            }
        }
    } );
    

    The above configuration will only run the eslint:partial task with the changed files, instead of running on potentially thousands of watched files.

    Here's another example, using the rewritesWatchedFiles flag. This flag is used to discard file changes while a file-writing task is being run, to work around triggering the task double or indefinitely:

    grunt.initConfig( {
        surveil: {
            options: {
                rewriteThreshold: 250
            },
            javascript: {
                rewritesWatchedFiles: true,
                src: ["gruntfile.js", "lib/**/*.js"],
                prepare: function( changedFiles, task ) {
                    grunt.config( "esformatter.partial", changedFiles );
                },
                tasks: ["esformatter:partial"]
            }
        }
    } );
    

    License

    This project uses MIT. See LICENSE file for additional information.

    Install

    npm i grunt-surveil

    DownloadsWeekly Downloads

    3

    Version

    0.1.2

    License

    MIT

    Last publish

    Collaborators

    • peol